MIG welder Ireland and a few welding tricks with WeldingSuppliesDirect? How to pick a welder tips: Duty cycle: The advertised amperage of the machine offers a headline guide, but the duty cycle of the machine gives up the truth. Light industrial machine duty cycles can be as low as 20%, but more heavy duty MIG’s should range between 40-60%. If a 300amp MIG has 30% duty cycle for instance, it’s on the edge of acceptability. Duty cycle is determined by how many minutes out of 10, it can weld at 100%. Duty cycle testing: MIGS tested at 20 Degrees & 40 Degrees we consider good. (Beware any manufacturer who doesn’t quote an ambient temperature for testing) Manufacturer’s warranty: Always a great guide to quality. A three year warranty is good. Weld characteristics: Make sure the arc is smooth & suits your application. (Some machines are better suited at the low range and others at higher amperage range).
Look for ways to create more efficiencies in the welding process. This includes examining such things as wire diameter, wire feed speed, voltage, travel speed, gas type, transfer mode, etc. For instance, if the shop is currently welding with a short arc process and a 75/25 blend of shielding gas, it may be more effective to switch to a different gas and a spray mode of transfer. Or, a change in process may be warranted based on the condition of the part. If there is oxide on the part, it may be easier to change to a process that will overcome contamination problems rather than try to clean each part before welding. Your welding supplier should be up to date on the latest technology and be able to advise you on new processes, machinery and consumables that can optimize welding at the shop. In some cases, it may be better to double bevel a joint to prepare it for welding rather than single bevel it. It is recommended to double bevel any material that is more than 3/4″ in thickness. Just this simple change in procedure can save quite a bit in weld metal. On a 3/4″ thick piece, a double bevel will use 1.45 lbs. per foot of weld metal while a single bevel will use 1.95 lbs. per foot.
Gasless welding, which is also called “Gasless” or “No-Gas” welding, is the main convenience of contemporary MIG welders. That means they can make welds either with or without gas. It is possible thanks to the use of a special tubular wire filled with a flux and metal powder called a flux-cored wire. In a nutshell, when a flux-cored wire is used, its components generate a shielding gas under a high temperature that is essential for a high-quality joint. The thermal overload protection is also a useful feature that will switch the unit off automatically if the temperature reaches a certain level. Surely, a MIG welder is not something you will carry every minute. Yet, if a machine is lightweight and fitted with wheels, using it will be much more pleasurable. Finally, pay attention to the kit each tool comes with. Some models include a welding shield, coil, attachment for flux-cored welding, hammer, or brush. So, take these features into account when buying a welder. Read extra details at Plasma cutters Ireland.
The Hobart Handler 230 is unmatched in its field. It’s a powerful welder that can comfortably weld 1/2 inch steel in single phase with fantastic arc quality. Other features include a 60% duty cycle at 175A, 12 different voltage settings, and infinite wire speed control. It’s a huge unit, but there’s wheels to help move it around, and a build in cylinder rack to store your gas cylinder. Most hobbyists won’t need a welder this powerful, but if you want a reliable MIG welder with a bit of extra power, this is our top pick. You can read the full review here.
Some tips about welding equipment, MIG and TIG welders, plasma cutters. TIG Welding / Gas Tungsten Arc Welding (GTAW) — TIG welding is an arc welding process that uses a non-consumable tungsten electrode to produce the weld. The weld area is protected from atmospheric contamination by a shielding gas (usually argon) and a filler metal, though some welds, known as autogenous welds, do not require it. A constant-current welding power supply produces energy that is conducted across the arc through a column of highly ionized gas and metal vapors known as plasma. TIG welding is most commonly used to weld thin sections of alloy steel, stainless steel and nonferrous metals such as aluminum, magnesium and copper alloys. The process grants the operator greater control over the weld than other welding processes, allowing for strong, high-quality welds. TIG welding is comparatively more complex and difficult to master than other processes and is significantly slower.
USA market look: Forney Industries is an American company that was founded in 1932. Forney’s 309 140 is affordable and able to weld many metals. As you’ll see below, its duty cycle is hardier than most, so you can work for much longer without breaks. It is about the same price is the Hobart 500559 Handler 140, but you’ll that the Forney is less suitable for any heavy-duty welding projects you might want to commit to. Therefore, the Forney is ideal for household use, provided that the use isn’t too demanding. It welds up to ¼ inches and includes flux core. It is capable of welding mild steel, stainless steel, aluminum, and cast iron. The Forney is able to use 4 inch and 8 inch wire spools. The cast aluminum wire feeding system ensures that the wire won’t tangle as much while it’s fed through. Find extra info at https://www.weldingsuppliesdirect.ie/.